X100 · Unmanned Ground Vehicle

The research platform that goes outside.

X100 is a stainless-steel, four-wheel-drive UGV built for labs that need to test on real terrain, not on lino. ROS on board, 75 kg of payload capacity, hot-swappable batteries, and mounting surfaces on every face. Bolt on your sensors and start collecting data the same week it lands.

X100 UGV in the field
X100 drivetrain and lug-tread tyres
X100 with manipulator arm
X100 outdoor test run
X100 compute and sensor deck
X100 configured as a ROS research robot
Deployed · field trials
75kg
Payload
0.8m/s
Top speed
4hr
Nominal run-time
40cm
Width
ROS
API, out of the box
X100 platform, wide field view
X100

UGV for robotics research & rapid prototyping.

01 — Platform

One base.
Every project.

Most research platforms ask you to design around them. X100 does the opposite: a flat, low-slung chassis with mounting points front, rear and top, fused power rails at 24V/12V/5V, and USB 3.0 and Ethernet brought out to the deck. Whatever you are building — a delivery stack, a lunar-analogue rover, an underground inspection unit — the vehicle underneath stays the same.

X100 chassis
Batteries

Two 24V packs ship with every unit — one in the robot, one on charge. Swap them in seconds without powering down, and the run never ends at the battery.

Payload mounting

Mount on top, front or rear. A deliberately low centre of gravity keeps the vehicle planted across payload sizes, so an arm on the deck does not cost you stability on a slope.

Manual override

A Bluetooth PlayStation controller drives the vehicle straight out of the crate, and takes it back whenever the autonomy stack needs to be interrupted.

02 — Subsystems

Built to be
argued with.

Three layers, each specified so you can check it against your own requirements before the purchase order goes anywhere.

X100 drivetrain and lug-tread tyres
Mechanical

Rugged multi-terrain platform

A stainless-steel body over four individually driven wheels on lug-tread pneumatic tyres. Enough torque to keep moving through mud, gravel and loose slope — the conditions the paper actually has to be written about.

  • Stainless-steel chassis, 760 × 400 × 510 mm
  • 4 individually driven wheels, 0.8 m/s top speed
  • Pneumatic lug-tread tyres, low centre of gravity
X100 compute bay
Compute

Nvidia Xavier NX, on board

Ships with Linux installed and enough headroom for machine-vision and learned-policy workloads at the edge. If your stack needs something else, the compute bay is customisable.

  • Linux pre-installed, ready on first boot
  • 2 × USB 3.0 and 1 × Ethernet brought out to the deck
  • 24V, 12V and 5V rails, each fused at 3A
ROS
Software

ROS, out of the box

Published topics for drive, odometry and power on day one. No driver archaeology, no reverse-engineering a CAN bus before the first experiment.

  • Documented ROS API, drive and telemetry topics
  • Bluetooth PlayStation controller for manual override
  • Getting-started guide with wiring and API reference
03 — In the field

Units on
the ground.

X100s in service with labs and R&D teams — configured with manipulators, LIDAR masts and custom instrument decks.

X100 mobile manipulator configuration
Mobile manipulator configuration
X100 export unit, Spain
X100 sensor mast
X100 field test
X100 outdoor run
04 — Footage

Watch it
move.

Unedited runs over the terrain the vehicle was specified for.

06 — Where it goes

Two ways
labs use it.

The same vehicle serves the algorithm bench and the application programme. Most groups end up doing both on one unit.

A test bed you can trust to repeat

Same vehicle, same odometry, same power budget every run — so the variable under test is the one you changed.

  • Autonomous navigation and SLAM development
  • Algorithm development and outdoor testing
  • Teaching platform for graduate robotics courses
Robotics research
Image slot
Robotics research

Programmes headed for the field

Where the deliverable is a working system, not a paper. The chassis takes the abuse while your team iterates on the payload.

  • Space and planetary-analogue robotics
  • Mining and underground inspection
  • Security patrol, delivery and agriculture trials
Applied R and D
Image slot
Applied R and D
07 — Specification

X100,
on paper.

Full technical specification. The spec sheet PDF and the getting-started guide carry the wiring diagrams and API reference.

Size
760 × 400 × 510 mm
Length × width × height
Weight
75 kg
Payload
Up to 75 kg
Drive
0.8 m/s top speed
4 individually driven wheels
Computer
Nvidia Xavier NX
On-board computer is customisable
Battery
24V 24Ah SLA, hot-swappable
Upgradable to Li-ion
Communication ports
2 × USB 3.0 · 1 × Ethernet
Power ports
24V · 12V · 5V
Each fused at 3A
API
ROS
Manual control
PlayStation controller
Via Bluetooth
Connectivity
WiFi · Bluetooth
Upgrades
Li-ion battery packs

Put one in your lab.

Tell us the payload, the terrain and the timeline. We will come back with a configuration, a price and a delivery date.